Support - FocusCalm

FocusCalm FAQs

How do I install the sensors into my FocusCalm headband?

Remove the sensors from the pack included with your headband by carefully pushing them out of the packaging. Align the small tab on the sensor with the notch found in each of the sensor positions on the headband. Press them carefully into each of the three positions on your headband making sure the sensor tabs are aligned with the notches on the headband.

Where can I find the SN Code for my FocusCalm headband?

Your headband has two extendable areas, one on each side of the headband. Pull gently to expose the inner rails. On the inside of the rail above the behind-the-ear sensors, you will see three rows of text. At the end of the top-most row (beginning with ‘SN’), you will see a code that ends with 4 numbers and letters. Carefully note the last 4 characters...This is your SN code.

How do I prepare the FocusCalm headband to connect?
  1. Power On Your Headband
    • Look for the 5 small LED lights above the ear hook on your headband. If you see lights flashing across the display, your headband is powered on. You may skip to the ‘Perform a Reset’ section.
    • If you don’t see any lights, press and hold the power button directly above these lights long enough to see all 5 lights illuminate in order from left to right, then let go of the power button. If, after doing this step, no lights are blinking, your headband may need to be charged. Use the included MicroUSB cord and an available USB power source (not included) to fully charge your headband before use.
  2. Perform a Reset
    • Once powered on, you should press and hold the power button for at least 10 seconds to reset the device. You will see each of the 5 lights illuminate in order from right to left and then go dark, but continue to hold the power button until all 5 lights turn on again. They will begin flashing outward from the middle. Your headband is now ready to connect.
  3. Please go to the “My Headband” section in the app and follow the instructions to connect your headband.
How do I wear my FocusCalm headband?

Position the headband on your head, making sure the center sensor is positioned above the bridge of your nose on your forehead, approximately mid-way between your hairline and eyebrows. The two sensors on the ear-hook should be snug behind your ear and be making good contact with your skin. Make sure there is no hair or anything else between the sensor and your skin at each contact point.

 

How do I turn on my FocusCalm headband?

Press and hold the power button to see all 5 lights illuminate in order from left to right, then let go of the power button.

 

How long should this device be used at a time?

Our daily training is designed to be 10-20 minutes, but you may use the headband for as long as you’d like and use it for multiple sessions per day.

What does the light on the FocusCalm headband mean?
  • Glows solid blue: Calm
  • Glows solid yellow: Aware
  • Glows solid red: Focused

 

How can I get more accurate data from the FocusCalm headband?
  1. Make sure the power is at least 20% of the maximum charge. Once all LED indicator lights glow solid white light, your headband is at maximum charge.
  2. Wipe the sensors with the included saline wipes weekly and change the sensors every 6 months.
  3. Ensure there is no hair between the sensors and your skin. Make sure the sensors are securely touching your skin.
How long will it take to see results?

Some people report seeing results immediately, and some after several sessions. You should plan on completing at least 20 sessions.

What is Neurofeedback?

Neurofeedback is also called EEG biofeedback or neurotherapy. It makes use of the brain’s ability to change and reshape brain networks. Neurofeedback training can be used to sharpen attention, relieve stress, enhance your mood, and improve your learning and behavioral control. Although the technology is complex, the process is simple. You will learn to alter your brain activity the same way you learn every other skill. You learn through feedback and practice. With neurofeedback, you get instant feedback about changes in your brain’s activity. Every half-second, your brain activity is compared to your target or goal. You can then learn and practice how to influence your brain activity to move closer to your goal.

 

How do I charge my FocusCalm headband?

To charge the headband, plug the charging cable into the USB port on your computer or another power source. The LED indicator lights will progressively illuminate on your headband as it charges. Each light represents 20% of the maximum charge. Once all five lights glow solid white light, your headband will be fully charged.

Can I create multiple accounts with one FocusCalm headband?

There is no limit to the number of users that can use one headband. Each user just needs to set up an individual account on their mobile device or tablet.

If you are using one mobile device or tablet, you just need to sign into/out of your account to switch users. To sign out of the app click on the 'settings' tab and scroll all the way to the bottom of the screen then click on 'sign out'. It’s important for each person to have their own account. If one account was used by multiple people it would cause the brain data to be inaccurate and skew each person’s results.

 

My FocusCalm headband is not working properly. What do I do?

Here are three steps you can take if your headband isn't working properly:

  1. Reset the headband—With your headband powered ON, press and hold the power button for at least 10 seconds to reset the device. You will see each of the 5 lights illuminate in order from right to left and then go dark, but continue to hold the power button until all 5 lights turn on again, then begin flashing outward from the middle. Your headband is now ready to connect to your mobile phone. Then follow the instructions on the app to connect the headband to your mobile device.
  2. Wipe your sensors with the included saline wipes weekly to keep the sensors clean and extend their lifetime.
  3. Replace the sensors when necessary to ensure signal quality. The recommended time is 6 months.
How do I contact support?

If you are still having trouble after completing all of the steps above, please contact our support team via email. They will help you to troubleshoot your device and help you to find a solution.

Please send an email to support@focuscalm.com

  1. Your order number
  2. The First and Last Name used when the order was placed
  3. The reason for return or explain the defect
Close Bitnami banner
Bitnami